Cisco WAP321 Firmware Download

Cisco WAP321 Firmware Download

Cisco WAP321 Firmware upgrade and mibs files Download
Cisco WAP321 Firmware
Cisco WAP321 Firmware Download - The Cisco WAP321 is a selectable dual-band 802.11abgn AP with an increase of features than I likely to find inside its unassuming softly-rounded beige plastic material enclosure. Number 1 shows the trunk panel. A couple of three bi-colored lamps at the top of the WAP--power, WLAN and LAN--that change and display color to point position. As the Cisco WAP321 itself has Kensington locking slots on its rear and front, the bracket itself does not have any. Nor is there other features to lock the AP set up. The trunk shroud addresses the plug-ins and on / off switch and has a knockout for cable tv routing and a opening for reset switch gain access to.

Cisco WAP321 Firmware Upgrade
The priced on / off switch is kind of an peculiar touch, because the WAP321 doesn't feature a 12V/1.0A power and the energy switch fails when the AP is PoE-powered. I used a incurred power in one of the new Linksys EA series, which worked fine just. Unfortunately, Cisco does not have a web emulator to enable you to take the WAP321 for a try. Among the simple things you should get with a far more expensive AP is more knobs to twiddle. Figure 6 shows the air settings that you can play with. Recognized settings are 802.11a, 802.11b/g, 802.11a/n, 802.11b/g/n (default), 5 GHz 802.11n and 2.4 GHz 802.11n. Transmit electricity can be cranked down (only) to 50, 25 and 12%.

Download Cisco WAP321 Firmware
One bandwidth control feature it doesn't require 802.11e is Bandwidth Usage. You simply place a share (the default is 0) of radio bandwidth you can use prior to the AP prevents allowing new consumer associations. That is a straightforward way to avoid specific APs in multi-AP installations from becoming overloaded. The WAP321 helps two cellular bridging methods. WDS bridge facilitates up to four organizations with static WPA2/AES or WEP encryption. WDS bridge partners automatically also work as repeaters; there is absolutely no way to make a closed bridge (block client association) apart from to not supply the encryption key to users. asfafirmware.com provide download link for Cisco WAP321 Firmware. you can download firmware and mibs file on this site at link below.

Cisco WAP321 Wireless-N Selectable-Band Access Point with Single Point Setup



  • AP/WDS Bridge/WDS Repeater modes
  • MAC address filtering
  • Management access control
  • IPv4, IPv6, MAC Deny/Permit ACL
  • HTTP/HTTPS/Telnet/SSH/Bonjour/SNMP v3 administration
  • Cisco WAP321 Auto-channel selection
  • Bandwidth utilization (% of AP bandwidth used before AP stops allowing associations)
  • Diffserv based client QoS
  • Transmit power adjust
  • Multicast and Legacy Rate setting
  • MCS setting
  • Rogue AP detection
  • WAP and Station Enhanced Distributed Channel Access (EDCA) QoS (802.11e)
  • Cisco WAP321 TSPEC support
  • Internal and syslog log support
  • LAN and WLAN traffic statistics
  • Packet capture
  • 802.1d Spanning Tree support
  • Client bridge mode (no WDS required)
  • Eight SSIDs
  • Cisco WAP321 SSID broadcast control
  • 1 management VLAN plus 8 VLANs for SSID
  • SSID to VLAN mapping
  • Client limit (32 maximum, 20 active recommended)
  • 802.11i preauthentication for fast roaming
  • IPv6 Host, RADIUS,syslog, NTP support
  • Cisco WAP321 Wireless enable/disable scheduling per SSID
  • WiFi Protected Setup (no physical pushbutton)
  • WEP, WPA/WPA2 Personal and Enterprise security


Download Cisco WAP321 Firmware and MIB


Go to Download Page

Download Cisco WAP321 Firmware

Cisco WAP321 Firmware image 1.0.6.2
Cisco WAP321 Firmware image 1.0.5.3
Cisco WAP321 Firmware image 1.0.4.4
Cisco WAP321 Firmware image 1.0.3.4

Download Cisco WAP321 MIB File

MIB file for Cisco WAP321 firmware image 1.0.6.2

0 Response to "Cisco WAP321 Firmware Download"

Post a Comment